General Support (Softaculous) <![CDATA[Problem create template - No snapshot found]]> Array
    [0] => No snapshot found
    [1] => There was an error creating the VPS Template

i try create template of ubuntu-18

Tue, 18 Sep 2018 17:37:40 GMT
<![CDATA[error:The viifbr0 is not started. Please run service virtnetwork start, Hetzner Dedicate]]> You need to enter enp4s0 as network interface name in configuration->Slave settings .Make sure ifcfg-enp4s0 has ip address, netmask and gateway entries .Then try to start virtnetwork service.
Tue, 18 Sep 2018 07:30:57 GMT
<![CDATA[error:The viifbr0 is not started. Please run service virtnetwork start, Hetzner Dedicate]]>
The viifbr0 is not started. Please run service virtnetwork start


No file appears / ifcfg-eth0


[root@176 sysconfig]# cd /etc/sysconfig/network-scripts/
[root@176 network-scripts]# ls
ifcfg-enp4s0  ifdown-ppp      ifup-ib      ifup-Team
ifcfg-lo      ifdown-routes    ifup-ippp    ifup-TeamPort
ifdown        ifdown-sit      ifup-ipv6    ifup-tunnel
ifdown-bnep  ifdown-Team      ifup-isdn    ifup-wireless
ifdown-eth    ifdown-TeamPort  ifup-plip    init.ipv6-global
ifdown-ib    ifdown-tunnel    ifup-plusb  network-functions
ifdown-ippp  ifup            ifup-post    network-functions-ipv6
ifdown-ipv6  ifup-aliases    ifup-ppp    service
ifdown-isdn  ifup-bnep        ifup-routes
ifdown-post  ifup-eth 

Please Helpme...]]>
Fri, 14 Sep 2018 16:12:44 GMT
<![CDATA[Config and Routing of Subnet in Virtualizor]]>
Quote From : quickbooks2018 February 7, 2018, 3:26 pm
Quote From : thornz July 6, 2016, 7:13 am
i have fixed it by adding my subnet's first ip as gateway and removed manually created bridge. thank you

Dear Support,

I bought your Virtualizor Panel, I installed Virtualzor on Hertzner Server.

I have created the viifbr0 all is well, Created Centos VM but machine has no

internet connectivity, please guide


I fixed the issue by adding

iptables -t nat -A POSTROUTING -o viifbr0 -j MASQUERADE
Mon, 10 Sep 2018 07:11:49 GMT
<![CDATA[Libvirt - error : virNetSocketReadWire:1808 : End of file while reading data: Input/output error]]> ]]> Fri, 07 Sep 2018 11:38:07 GMT <![CDATA[DNS format for VPSs]]>
Quote From : jevingala March 15, 2018, 6:22 am
in which 'format' should be the DNS be writen?:

Though its not necessary to fill those fields, since it will be taken from ip pool .

Please delete the spams below and block the idiots!!!
Fri, 07 Sep 2018 11:22:02 GMT
<![CDATA[KVM VM password reset]]> Vps created by iso should only have 1 standard partition '/' with ext4 file system and then create template from it and check.]]> Thu, 06 Sep 2018 05:32:38 GMT <![CDATA[KVM VM password reset]]>
I got the issue again which is not function when my VM is built by ISO.

That is a CentOS 7 with multi partitions. 

Could you please advise?

Thu, 06 Sep 2018 04:19:31 GMT
<![CDATA[there was an error in setting the root password of the new vps]]> After yum update and reboot of server the issue was resolved.

Wed, 05 Sep 2018 06:50:26 GMT
<![CDATA[KVM Network erroe]]> Please confirm if you have added the ip pool using this guide :
If you still face the issue then please open a support ticket so that we can check the issue.

Wed, 05 Sep 2018 05:39:01 GMT